• 목록
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Repairing a broken door hinge is a simple task for most homeowners. If, however, the screw holes are damaged and aren't able to hold screws, you might have to add dowels and wood glue before you can put back the hinge.

Clean up any surface rust. This will help the dowels stay in place and give them a solid foundation to grip into.

Remove the Hinges

A variety of door hinges can be removed, which makes it easier to move the door from one end of the frame to the other or take the entire door off when needed. Anyone with a little patience can remove the hinges, however, you must know what to do.

If the hinges have been painted, you'll need to take window blown off hinges the paint prior to trying to remove the pins. You may scratch your door if you do not remove the paint. Put the hinges in a stainless steel pot and fill it up with water until the hinges are submerged. Allow the hinges to sit in the pan for about 30 minutes. The heat from the water will soften the paint and make it easier to take off the pins.

After the pins have been loosen and the pins are loose, you can take off the hinges from the door and frame. It is possible to use a standard screwdriver, however you should use a magnetic screwdriver for this job. This type of screwdriver is specifically designed to grab metal screws and will assist you in getting the task accomplished much faster.

It is a good idea to spray some lubricant on the hinges before attempting to remove them. A simple lubricant can make the process to go more quickly and make it easier to remove the pins and screws. This kind of lubricant can be found in a variety of hardware stores as well as home improvement shops.

You should also keep in mind that the number of hinges you'll require will differ based on the door's type and the setting. Heavier doors and solid-core doors will need more upvc window replacement hinges, while hollow-core doors that weigh less might require just two or three.

Understanding the different kinds of hinges will help you decide which one is the best for your particular situation. Exterior hinges are designed to hold the weight of a door, whereas interior hinges need to be able to handle heavier loads.

Reattaching the Hinges

Sometimes, the hinges on doors become looser over time and begin to hang out of alignment or slide. It could be a huge problem, but the fix is usually quite simple. A simple tightening can solve the problem. If the screw holes have been stripped out, it could be difficult to fix. Fortunately, there is a trick to make these holes back to their original size using a wooden dowel.

Start by drilling the old hole using a drill close to the new screw size (normally 3/8"). Fill in the hole using wood glue and a wooden stick. To ensure a secure fit, the dowel should be cut to the same length as the screw. Reinstall the screw and tighten it to the desired degree of tightness. If the door continues to bind up, add another dowel to the gap. Repeat the process. Make sure to close the door slowly so that you can verify the clearances at the perimeter after each adjustment.

You could also use a wood plug in place of the dowel. This is also a viable option however it may take a bit longer to install. You can use a piece of wood that has been whittled to the right size. If you don't have a woodworking tool, you can also make use of toothpicks or wooden matches.

Use a countersink to make the hole smaller than the head of screw after you have put it back in place. This will prevent the screw from rubbing against the edges of the doors when they are closed and opened. This will make it easier to tighten the screws after replacing hinges.

After reinstalling the hinge, apply lubrication to the hinge using a dry lubricant. This will prevent it from becoming stuck in the future. Products such as PB Blaster or Liquid Wrench are good alternatives. Apply a thin coat and give it approximately 15 minutes to reach the hinge barrel.

Refinishing the Hinges

If you're not ready to replace the hinges on your door, you can make a few repairs. Verify that the screws that hold the hinge plate in place to the door frame and the frame are tight. If they're loose, tighten them using an electric drill or screwdriver. Be careful not to tighten the screws so much that they start to cause gaps at the trim joints, or worse remove the threads.

If the problem is the hinge plates are breaking and you want to reattach the plates by putting wood glue on the back of them and inserting wooden dowels or toothpicks into the holes. The toothpicks or dowels will serve as a solid base for the screws and help keep the plates from moving when you drive them into position. Let the glue dry before reattaching the hinge.

The screws could also be damaged or missing. It is possible to fix this issue by replacing the screws with longer ones. Use a drill bit that is the same size as the screw hole to prevent drilling into the jamb or hinge.

Close the door after you've reattached your Repair Upvc window hinge and check the gap between the frame and the door. The gap should be about the thickness of a penny all around or less if the old door was hung incorrectly. If the hinges were installed properly, this shouldn't be an issue.

If the hinges are still loose, you could add an extra thick hinge between the hinge plate's surface and the mounting surface. This will give the hinges more room. You can also try removing the hinge pin from the problematic hinge and then pounding it using a hammer to make it tighter or use an entirely new casement window hinge replacement pin. You can also grease your hinges with mineral oil or jojoba to reduce friction and help keep them in place. Lubricating your hinges regularly will help keep them from becoming stiff and squeaky and also extend their lifespan.

Cleaning the Hinges

The friction created by a hinge's constant movement draws dust particles. These particles can get stuck tilt and turn windows hinges accumulate in the moving parts of door hinges, if they're not maintained and cleaned regularly. The hinge will become stiff and creaky and its appearance can rapidly change. Regular cleaning, lubrication, and inspections will maintain the functionality and quality of hinges on a door.

Check the hinges to see how much rust has formed on their surfaces. If the rust has become so severe that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace the hinges. If you are able to save the hinges, remove any loose rust using wire brush and steel wool. Apply a commercial rust removal solution or a homemade solution such as lemon juice to the hinge. Allow the rust remover to sit on the hinge for a few minutes to penetrate and dissolve any remaining rust.

If you don't want to spend cost and time to replace your hinges, simply retightening the screws will make the hinges functional again. It is possible to add dowel or shim made of wood to the hinge when the screws have been shaved. Wooden dowels are round pieces of wood in the form of rods, which are available in various lengths and sizes. You can find them at home improvement centers as well as woodworking supply and craft shops, or online.

You can also make an shim out of metal or plastic depending on the kind of hinge you own. To make a dowel, cut an unfinished dowel into the desired length. You can then dip the dowel in carpenter's glue before inserting it into the stripped hole, allowing the glue to hold the dowel in place.

Before cleaning the hinges, put down a cloth or towel to protect your flooring from spills. After the area is secured then clean the hinges with an absorbent sponge or a soft cloth that has been soaked in mild cleaner or vinegar to remove built-up dirt, grime and tarnish. You can make use of a toothbrush or a small brush to get into difficult-to-reach areas in tight spaces and crevices.