• 목록
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Replacement Door Handles

Over time the handles on your doors will wear down and will require replacement. It is important to keep the same dimensions as the handles you have previously replaced when replacing them.

The top screw position as well as the lever and keyhole size are the three measurements you need to verify. Use the size guide to assist you.

Inline Lever/Lever

A lever handle is a modern door handle that is designed to fit new or replacement handles for windows doors. This type of door handle is available in a wide range of styles and finishes. This handle is offered by several manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite door handles are made of robust materials and are suitable for multi point lock doors that require a strong design. The handles are inline and use the same spindle and screws to secure them. They are easily fitted on new or existing uPVC/Composite doors.

The handle can be adjusted and angled to accommodate any user. The handle has been tested to 200,000 cycles, this will ensure the quality of the finish as well as the performance of the handle over time. The sprung lever can be cut to fit a wider range of locks. This is particularly useful for narrower doors where the cylinder is situated further back in the door. A shortened lever is also an ideal choice for doors where the latch can be opened by a thumb turn located on the inside.

Lever Pad

A Lever Pad door handle made of upvc functions differently than lever handles found on most doors. These window handle upvc types can either operate from a single spindle (inline) or independently from each side by using two offset spindles or inline (pad). They are typically used on UPVC double glazed handles glazed doors and come in many variations & finishes.

The handles are available in a variety of finishes, including White, Chrome, and Gold. The finish is compliant with BS EN 1670:2007 Grade 5 and is also resistant to corrosion, giving the handle a high degree of durability and performance for the intended use.

All of the UPVC handle lever pad styles are supplied with a spindle and screws that allow them to be installed on a new or existing uPVC door. The backplate fixing centres of 211mm allow for a wider size handle that is often a benefit when replacing a faulty or worn multi point door lock mechanism. These handle levers are also sprung, solving the problem of door handles sagging from their horizontal position when they are not in use.

When selecting a replacement double glazing window handles UPVC handle and spindle, it is essential to match the PZ dimensions of the multipoint lock as well as the uPVC door. This measurement can also be called 'handle centre or cylinder centres'. It is important to match the correct handles.

After you have determined the proper PZ size it is important to ensure that the lever and push pads are shaped to fit the American with Disabilities Act compliant handles that you need for your door. They typically have a square or round design with an internal lever and external push pad.

The majority of UPVC lever pads that we sell are sprung, meaning that they return to their horizontal position when they are not being used, instead of hanging out and possibly securing in the frame. This prevents drafts and cold air from entering a home. You will also find that the majority of the UPVC lever pad handles are handed which allows you to place them on either side of the door.

Euro Cylinder

Cylinder locks are commonly found on uPVC doors, but can also be found on other types of door. The cylinder lock is operated by a key which unlocks the cylinder case. This exposes pins that can be aligned to those in the lock, and permit them to turn the camera that rotates, opening the door. Euro cylinders can be fitted with up to six pins, with external and internal doors typically having different levels of security.

The choice of cylinder you choose is essential. It is based on the type of use your doors and handles receive. External doors, for example should be equipped with cylinders with greater security while doors inside can be secured using the standard cylinder. In addition, some cylinders come with additional features which can enhance security even more, like anti-drill and anti-bump characteristics.

A euro cylinder must be measured accurately to ensure that it is the correct size for your door. The cylinder should be measured from the central fixing screw hole to the end of the cylinder, including the thumb turn if you have one. If you cannot measure with the lock in position, you can remove it. A cylinder that protrudes beyond the handle and escutcheon might be susceptible to attacks like snapping locks, therefore it is crucial that it is not too long.

Most newer cylinders have been designed with anti-drill and bump resistance features built into their design. These features are designed to minimize the chance of a attack by forcing the cylinder to rotate in an opposite direction. This can help stop the attack and protect your doors.

There are cylinders that have been designed to withstand snapping. This is an increasingly common type of attack on cylinders, where the break line in the lock is smashed by a tool that is specially designed to break the front of the cylinder and allow the door to open. This is faster and more straightforward than gaining access through multipoint locks. It also leaves no evidence of a burglary, which can hinder the insurance claim.

Spring Cassette

This spring cassette is found within the base plate of the door window handle repair. It is a spring-loaded solution to help return your multipoint lock handles back to their original position after use. In the past, a lot of these types of handle did not have a spring integrated into them, and without it they tend to droop or 'drop' once the locking mechanism is removed. This simple component is the most effective way to address this issue. It also prevents your door from becoming stuck in the closed or open position as they aren't easy to close manually.

These spring cassettes are specially designed for use with sprung multipoint locks but they won't work with non-sprung multipoint handles. You will need to have a hole specifically cut in your backplate in order for them to fit (please look at the image for a technical diagram). They are a replacement for existing damaged or missing cassettes inside the backplate of the door handle for various kinds of uPVC doors. They are available as a single unit. They come with a square cut out that accommodates an 8mm shaft.

These spring cassettes are an excellent value solution for the problem of door handles that are sagging. They are simple to install and will increase the lifespan of your uPVC door. Contact us for more information about our wide range of uPVC accessories and spares. We are here to help and happy to give you professional advice.